SUMIFITT® is water-based polyolefin emulsion with strong adhesion to hard-to-adhere material, polypropylene (PP). Moreover, SUMIFITT® expresses the adhesion by lower heat treatment temperature than general adhesive for PP. Therefore, it can reduce energy consumption in the adhesion process.
1. Excellent Adhesion to PP
Polymer structure nature of SUMIFTT® with high affinity to PP makes it possible excellent adherence to PP. Moreover, it can also adhere to homo-PP, which is difficult to adhere.
Composition: PP composite material/Coated sample (Thickness: 10μm as solid)/Coating agent (Thickness: 100μm as solid)
Coating condition: Degreasing →Coating of SUMIFITT® or Conventional adhesive for PP →Drying (50°C, 5min) →Coating of coating agent →Heat treatment (80°C, 30min)
Peeling condition: Apply cellophane tape to cover the cut area and peel it at the angle of 45°
2. Lower Temperature for Bonding
SUMIFITT® consist of a special polymer with optimized crystallinity and flexibility. Therefore, it can strongly adhere even at lower processing temperature. It contributes to reduction of energy consumption and CO2 emission in the adhesion process.
Composition: PP composite material/Coated sample (Thickness: 10μm as solid)/Coating agent (Thickness: 100μm as solid)
Coating condition: Degreasing →Coating of SUMIFITT® or Conventional adhesive for PP →Drying (50°C, 5min) →Coating of coating agent →Heat treatment (Given temperature, 30min)
Peeling condition: 180°peel test (50 mm/min)
3. Multi-material Adhesion
SUMIFITT® could be applied to various resin kinds and metals.
Composition: Material/SUMIFITT® (Thickness: 10μm as solid)/PP sheet
Coating condition: Degreasing →Coating of SUMIFITT® →Drying (60°C, 5min) →Set of PP sheet →Heat press (Plastics: 0.1MPa, 150°C, 1min; Metals: 0.1MPa, 150°C, 2min)
Peeling condition: 180°peel test (100 mm/min)
4. Performance Improvement of Different Types of Emulsions
Combination of SUMIFITT® with different kinds of emulsions such as polyurethane and acrylic one improves PP adhesion. Blending of SUMIFITT® could enhance the performance of adhesion by changing the characteristics of new emulsion.
Composition: PP composite material/Coated sample (Thickness of solid: 10μm)/Coating agent (Thickness of solid: 100μm)
Coating condition: Degreasing →Coating of sample →Drying (50°C, 5min) →Coating of coating agent →Heat treatment (80°C, 30min)
Peeling condition: 180°peel test (50 mm/min)
Item | Unit | SUMIFITT® WR101 |
---|---|---|
Appearance | - | Milky white emulsion |
Solid content | wt% | ca.31 |
pH | - | 7-9 |
Viscosity | mPa・s | <100 |
Solvent content
(Alcohol) |
wt% | <1 |
*These values are not guaranteed.
SUMIFITT® shows good performance as adhesives or primers between PP and various materials.
Field | Application |
---|---|
Automobile | Primer for Bumper painting, Primer of adhesive for interior material, Adhesive for interior material, Adhesive for car battery, Adhesive layer for decorative film |
Home electric appliances | Paint Primer for housing, Primer for adhesive |
Electronic material | Primer for adhesive of electronic substrate |
Ink | Ink binder, Primer for printing |
Packaging | Laminating adhesive |
Building material | Primer for sealant |
Fiber | Fiber binder, Sizing agent for reinforcing fiber |
Here is our inquiry or sample request form.
Notes
Data shown here were obtained by using SUMITOMO CHEMICAL's methods.
These values are for reference only and are not intended as guarantees of product performance.
All the data given above are based on materials, information and data currently available and are subject to change in accordance with new findings.
©Sumitomo Chemical Co., Ltd. All rights reserved.